Test Apparatus

Product Details:

CARBONTEST kit introduces a new method of sampling, which is based on collecting the powder during a perforation carried out using a common percussion drill. A collecting device (picker), designed in careful detail to optimize the powder flow, has been developed to implement the method. Proper designing of the collection container allows to analyze the powder, making use of the chemical colour change of phenolphthalein in a quick and accurate manner.

The collection tool for the sample to be analyzed is especially light, handy and portableso as to allow analysis by a single operator without needing specialized technical help. The possibility of performing independently both the collection of the powder produced by perforation of the concrete item and the later analysis of the powdered material, simplifies the traditional analysis procedure and makes it especially cost effective and usable for a vast number of structures. CARBONTEST kit introduces a new method of sampling, which is based on collecting the powder during a perforation carried out using a common percussion drill. A collecting device (picker), designed in careful detail to optimize the powder flow, has been developed to implement the method. Proper designing of the collection container allows to analyze the powder, making use of the chemical colour change of phenolphthalein in a quick and accurate manner.

 

Products Features: The CARBONTEST Kit equipment complete with accessories and options includes:

Case 39x34x14 cm made of coloured polypropylene. Strong but light, it can house all the equipment needed to carry out the collection and analysis.

• Picker to collect the powder. The bottom part of the ring ends in a funnel leading the powder into the relevant test tube.
• Test tubes made of styrene acrylonitrile 18 cm long and with an inside passing width of 9 mm. The transparent container comes with a special thin cut along the generator of the container which lets through the chemical reagent while keeping the powder inside.
• Measuring Ruler with graded notches in cm and inches, designed to fit into the hole and to measure the powder collected in the test tube.
• Bottle 1% alcoholic solution of phenolphthalein , featuring a reaction range between pH 8,3 and pH 10,0 which determines a colour change to pink of the powder not affected by carbonation.
• Pasteur pipette which makes it simple and easy to place the phenolphthalein along the thin cut of the test tube.
• Cartridge of universal plaster for cement, 250 gr, suitable for smooth surfaces and for sealing the collection hole. Grey colour, it can be polished and painted for indoors and outdoors application with temperatures between +5°C and +30°C.
• Scientific carbonation text. “Carbonation corrosion in reinforced concrete structures” which analyzes the main causes and the phenomena governing the evolution and spread of carbonation in reinforced concrete structures. In Italian.
• Block of Survey sheets specially designed and studied in order to be used when performing the survey. These sheets can be used to write down the key information at the point of collection and the measurements made for each test.
• CARBONTEST® Report, a processing software for making out a technical report, organizing the results of the collection in summary sheets and setting up diagrams of propagation of carbonation in order to forecast the remaining life of the structure being analyzed.
• Guide to installing and compiling the report software.

 

Product Details:

An optical time-domain reflectometer (OTDR) is an optoelectronic instrument used to characterize an optical fiber. It is used for testing the integrity of fiber optic cables by verifying splice loss, measure length and find faults.

WORKINGIt sends pulses of light into optical fibers at a wide range of pulse widths.It analyze the little amounts of light reflected back to them from faults in the fibers.It then uses complex computations to determine the losses and distance to events encountered in the fiber.WHAT WE OFFERDynamic range, varied distance accuracy, measurement range, dead zones and sampling resolution to meet all the requirements of a user.Various sizes – Full Feature / Hand Held / Miniature.Ease of use – Portable / Ultra-Portable / Light / Compact.Built-in Power meter / Bluetooth OTDR to Display the traces on other devices like PC, Tablet or Mobile phone.Variable costs and various brands depending on the user’s budget.

Applications:
Create a ‘picture’ of newly installed fiber optic cable to compare at a later stage in case of any problem.Test long and short fiber cables (10m to 150km or more than 150km) and confirm the quality of fibers. Also shows the loss at connectors and splices.It also shows end of the fiber, location of connectors splices.OTDR is extremely useful to find out faults in all types fiber network like FTTx, CATV, Optical LANs whether it is break or imperfections, etc.

Sokkia B40aSokkia B40a is top of the line auto level for survey & distance measure. Sokkia B40a is rapid, accurate with ultra-short focusing of 20cm (7.9 in.). Best Choice Technologies is an authorized Sokkia auto level dealer.
All products you purchase from us are original Sokkia products. Sokkia products include Sokkia iM101 manual total station, Sokkia iM 55 total station, Sokkia CX 55 total station, Sokkia CX 65 total station, and Sokkia B40a. Get Sokkia manual total station price in India. Get Sokkia auto level price in India.
Sokkia B40a Features• Rapid, accurate, and stable automatic compensation• Ultra-short 20cm (7.9 in.) focusing• All-weather dependability• Clampless, endless fine horizontal adjustments
Sokkia B40a DescriptionRapid, Stable, and Durable CompensatorThe compensator of B20/B30A/B40A incorporates four suspension wires made of super-high-tensile metal that features minimal thermal expansion coefficient, providing unmatched durability and accuracy. Finely tuned magnetic damping system quickly levels and stabilizes the line of sight despite the fine vibrations present when working near heavy equipment or busy roadways.
20cm (7.9 in.) – Ultra-Short Minimum FocusB20/B30A/B40A can focus on objects at 20cm (7.9 in.) in front of the telescope. This feature dramatically facilitates the works in confined spaces.
Horizontal Circle for Angle MeasurementHorizontal angles can be directly read in 1° or 1gon units. Free rotation feature allows you to read any angle from zero.
All-Weather DependabilityWith the IPX6 rating, the instrument is protected against powerful water jets from all directions, meaning B20/ B30A/B40A withstands a sudden shower or torrential rainfall. The advanced protection design also deters clouding or condensation inside the telescope.
Sokkia Auto Level
Get Best Price for Sokkia Auto LevelSokkia B40a land surveyor is best auto level by Sokkia. Get best accuracy, best price for Sokkia auto level land surveying equipment in India. Sokkia B40a auto level is land surveying equipment used in construction business. The Sokkia B40a auto level land surveyor is one of the best auto levels of its kind.
Get Sokkia Auto Level best price and quotation. Fill enquiry form now.
Send EnquiryGet Sokkia auto level price.
Technical Specifications of Sokkia B40aModel Sokkia B40ATelescopeLength 214mm (8.42in.)Magnification 24xObjective aperture 32mm (1.26 in.)Resolving Power 4″Field of View (at 100m/328ft.) 1°25’ (2.5m / 8.2ft.)Minimum focus • 0.2m (7.9 in.) from end of telescope• 0.3m (1ft.) from instrument centerImage ErectStadia Constant 0Stadia Ratio 100Focusing Knob 1-speedSighting Aid Gun SightAccuracy (1km double run leveling)Without Micrometer 2.0mm (0.08 in.)With Micrometer n/aCompensatorType Pendulum compensator with magnetic damping systemSetting Accuracy 0.5″Working Range ±15′Circular LevelSensitivity 10′ / 2mmHorizontal CircleDiameter 99mm (3.9in.)Minimum Division 1°/ 1gonGeneralWater Resistance IPX6 (IEC 60529:2001)Operating Temperature -20 to +50ºC (-4 to +122°F)Size Width x Length x Height 122mm (4.8in.) x 214mm (8.4in.) x 140mm (5.51in.)Weight 1.5kg (3.3lbs.)

Determine the level of contamination in a sample; results are available within 15 seconds. These tests are based on the measurement of adenosine triphosphate (ATP), which is present in all animal, vegetable, bacteria, yeast and mould cells. Detection of ATP indicates the presence of contamination by any one of these sources. When ATP is brought into contact with the reagent combination luciferin/luciferase, a reaction takes place which emits light in direct proportion to the amount of ATP present. This instrument measures the amount of light generated and provides information as to how much contamination is present within 15 seconds!

EnSure is a quality monitoring system that uses a single instrument platform to collect,analyze and report data from multiple quality tests. The system is an easy-to-use,flexible, and accurate quality monitoring system for ATP surface hygiene, water monitoring, allergen prevention/high sensitivity, detection of Coliform, E-coli,TVC etc.

Additional Information:

• Minimum Order Quantity: 1 Number
• Delivery Time: 1 week

Product Details:

DFR Test Apparatus:

• Dynamic flow rate can be conveniently determined using this apparatus.

Principle:

• The time required for the powder contained in a tube to flow between the two fixed marks 30 cms apart out of a standard cone is measured and expressed as ml / sec
• The value is directly related to flow ability of the powder

The Apparatus:

These consists glass tube, standard brass cone, orifice, infrared sensors & digital display.

Product Details:

Box Compression Tester made of a set of plates one is attached to the load measuring arrangement and the other is movable plate which is move with the help of motor, gearbox, and screw and nut arrangement, the movable plate have the facility of over travel and under travel. The load measuring arrangement is digital type. The box of which the compression strength is to be determined is placed on the lower plate, due to the motion of the movable plate the box is compressed and the compression load is directly read out on the digital indicator on the panel. The deflection of the box also measured with the help of the digital deflection indicator.The instrument is made in two parts, one is for main instrument and the other is the control panel. The ultimate test is to determining overall quality and performance of the container. The instrument isb right chrome plating, zinc plating, painted in metallic paints. It is supplied complied with electrical which include micro-switches, Push buttons and contactors for safe and convenient operation.We provide the Window based software which gives the different measurement parameter and the graph. The report can be printout by using proper printer. The variable speed model speed is vary by aknob fixed on the panel and the speed also digitally indicated on the control panel of the instrument or by simply types the speed on the monitor of the computer. Different model have speeds suitable for testing different materials. Various built in safety arrangements such as over travel protection, are provided.

Technical Specifications:

• Capacity : 3000 kg
• Least Count : 1 kg
• Box Size : 450 x 450 x 450 mm
• Accuracy : ±1% on full-scale
• Load Speed : Variable speed from 50 to 500 mm/min
• Gearbox : Worm reduction gearbox
• Data Presentation : In Engineering Unit
• Power Supply : 440VAC, 50Hz, 3Ph.AC
• Control : Up, Down, Stop
• Related StandardIS : 7028 (Part VI) - 1987, IS: 7028 (Part IX) - 1987TAPPI : T 804 om-02ASTM : D 4577 – 94/D 642 – 98

Product Details:

Details:

• Anti-Trip Technology for complete trip free Loop testing on all RCDs rated 30mA and above.
• Dual Display allows simultaneous measurements like Loop & PFC/PSC.
• Two wire connection for Loop L-L, L-N and PSC testing is possible.
• Phase rotation, Voltage and Frequency measurements.
• Lock-down test button for 'hands free' testing with auto-start operation.
• Display and front panel keyboards with Backlight to be visible in dark places.
• Water and Dust proof (IP54)

Product Details:

The Coal Plastometer PL2000 is a fully automatic system for determination of fluidity of coal by the Gieseler method according to ASTM D 2639 and ISO 10329 Standards.

Solder bath stirrer in the plastometer headCrucible movement Fully automatic Temperature display Degree C Data print interval 60 sec Alphanumeric printer non impact type System diagnostics automatic at start up Host computer interface RS 232 CPower supply single furnace 230 / 120 V 0.8 max

Product Details:

This test determines whether tablets and capsules disintegrate within a prescribed time when placedin an immersion fluid under prescribed experimental conditions.
Features:

• Microcontroller based circuitry to precisely control, indicate and program temperature of water bathand beaker individually.

Pause facility: 

• This facility permits chemist tocheck disintegration state of the tabletsintermittently and continue test without disturbingthe test parameters.
• Maintenance free single stepper motor.
• All test parameters are indicated on graphic LCDdisplay screen.
• The status of the tablets can be checked with thehelp of 'PAUSE KEY'.
• Protection for over temperature for Heaterthrough software and hardware.
• Facility to observe stroke length while test is on.
• Validation of cycles / Min. with On/Off line printingfacility.
• Temperature of both beakers displayedindividually.
• Test reports print all the detailed test parameters with ON-LINE or OFF-LINE printing facility.
• Facility to print company’s name on test report.
• Optically isolated heater.
• Facility to review set parameters.
• Nonvolatile memory.
• Date selection in off line printing. 

Additional Information:

• Production Capacity: 50
• Delivery Time: ready

Product Details:

Main Features:

• Chinese and English menus, large LCD digital screen with rich menu content and complete functions.
• Automatic loading and unloading of load, simple operation, a high degree of automation.
• Hardness automatic display, high accuracy, small indication resolution, no artificial operation error.
• It can automatically identify the minimum thickness and super-domain warning of the specimen.
• It has a built-in micro printer, which can print average hardness, maximum and minimum hardness, and its hardness has discreteness.
• The RS232 interface can be connected with computer to save massive data and hardness analysis.
• It has an automatic conversion with other hardness. (HB, HV, etc.)
• It has one national intellectual property right.

Application Range:

• Rockwell: It is used to measure Rockwell hardness of ferrous, nonferrous metals and nonmetallic materials. It is suitable for measuring Rockwell hardness of heat treatment materials such as quenching and modulation.
• Surface Rockwell: It is used to measure the surface Rockwell hardness of the ferrous metal, alloy steel, hard alloy and metal after surface treatment (carburizing, nitriding and electroplating).
• Plastic Rockwell: Hard plastics, aluminum, tin, copper, mild steel, synthetic resins, and friction materials.

Product Details:

GLOW WIRE TESTER is designed to carry out fire hazard testing as specified in IEC 60695-2-10 2000-10. Flammability test is to check the ‘Resistance to Fire’ of electrical insulators that touch directly conducting parts & also parts of insulators. Testing with regard to fire hazards can be done by creating exactly the conditions occurring in practice.

Product Details:

The plunger penetration apparatus is used to determine the consistency of fresh mortar, building lime and masonry cement. The test apparatus consists of a base to place the test cup and a vertical column holding the penetration plunger assembly. The drop default height is adjusted to 100 mm. The plunger assembly weight is 90 g.

The plunger penetration apparatus is supplied complete with:

•  Test Cup, Ø 80 mm X 70 mm
•  Tampe

Additional Information:

• Item Code: ALFAPL01
• Production Capacity: 50
• Delivery Time: Ex stock
• Packaging Details: wooden

Product Details:

The apparatus comprises of the following.
Loading Unit: Supplied with load yoke with direct and lever system for applying load. Normal stress capacity 8 kg/sq. cm. Load is applied either directly or through a counter balanced detachable lever. Provision is made for the load to be applied either through a steel ball recessed in the loading pad or direct through a boss on the pre calibrated loading yoke. The loading unit is provided with V strips and roller strips for frictionless movement of shear box housing.

Shear Box Assembly:
Comprising direct shear box in two halves for a square specimen size 60 x 60 x 25mm one pair of plain gripper plates, One pair of perforated gripper plates, one pair of porous stones, one top of loading pad.

Shear Box Housing:

• Accommodates the direct shear box assembly.
• Complete with two ball roller strips.

Essential Accessories:

• High sensitivity compression proving ring. Cap 200kg. One consolidation dial gauge 0.01mm x 25mm and one strain dial gauge 0.01mm x 25mm
• Optional Extras: Additional set of weights to give a normal stress of 5 kg/cm2. Soil sampler for 60mm x 60mm specimen and test forms pad of 50.
• Spares:Porous stone for 60mm x 60mm size sample available in pairs.Unit is electrically operated to give the following 12 rates or strains. 1.25, 0.625, 0.25, 0.125, 0.05, 0.025, 0.01, 0.005, 0.002, 0.001, 0.004 and 0.0002 mm/min. The apparatus is suitable for operation on 230 Volts Single Phase A.C. Supply.

Additional Information:

• Production Capacity: 10
• Delivery Time: exstock
• Packaging Details: wooden

Product Details:

Consists of a torque head adjustable in height by means of a lead screw rotated by a drive wheel to enable the vane to be lowered into the specimen. Which operates a worm gear arrangement turning the upper end of a calibration torsion spring, vane dia, rod dia, vane size & vane height are as per IS specifications.

The vane shaft is attached through the hollow upper shaft to a resettable pointer, which indicates the angle indicates the angle of torque on a dial graduated in degree the dial reading multiplied by spring factor gives the torque a container for soil sample.

Product Details:

Product Details:

This is used for determination of in situ dry density of natural or compacted fine grained soil, free from aggregates. A cylindrical cutter is used to extract a sample of the soil with the help of a dolly and rammer. From the weight, density and the moisture, and dry density of the soil is ready calculated.

Additional Information:

• Production Capacity: 60
• Delivery Time: exstock
• Packaging Details: wooden

Product Details:

This apparatus is meant for determination of softening point of Bituminous materials according to IP 58 and IS 1205-1958. Softening point is that temperature at which the specimen under test becomes soft enough to allow a steel ball of specific dimension to fall a required distance under test condition. The apparatus consists of glass beaker, ring stand, two steel balls with ring and ball guides.
Optional

Abel Flash Point Apparatus is suitable for determining the close cup flash point of Petroleum and mixtures according to IP 33 & IP 170 and also IS 1448 (Part I) 1985 (P:20). It is suitable for oils whose flashes below 70°C. It is supplied with oil cup, cover fitted with stirrer, thermometer socket S.S. Water Bath, Stand. An electric heater is fitted at bottom for operation on 220 Volts AC Circuits. Following Models are available:-Abels Flash Point Apparatus electrical heating with Energy Regulator Control – Oil Test Jet.Abels Flash Point Apparatus electrical heating with Energy Regulator Control & Concealed Hot Plate – Oil Test JetAbel Flash Point Apparatus with Regulator DIGITAL TEMP. INDICATORAbel Flash Point Apparatus with Regulator, DIGITAL TEMP. INDICATOR with geared FHP. Elect. Driven Stirrer (120 R.P.M)Abel Flash Point Apparatus Temp. Range -18°C to +70°C with REFRIGERATION SYSTEM as per IP-70 with Oil Test Jet system. With digital temperature. Indicator and FHP motor stirrer.
Salient FeaturesOPTIONAL ACCESSORIES:Abel Oil Cup Thermometer (-35 / 70 C x 0.5°C) IP 74 CAbel Water Bath Thermometer (-30 / 80 C x 0.5°C) IP 75 CPolish Wooden caseSpare cup for above ApparatusSpare top (Cover Assemble) with Shutter mechanismSpare Nichrome Heating elementPendulum for Measuring Time in StrokesConcealed Hot Plate with housing

Product Details:

Vogel Test Apparatus is designed to induce anxiety within a subject and monitor the degree of drug effect by the administration of a mild shock after 20 licks on a sipper tube. The shock is delivered through the sipper tube and is maintained for a selectable duration of 0.25 to 2.0 seconds. The intensity of shock is user adjustable. With the onset of the initial shock, Anxiometer begins a three minute testing session during which the total number of licks and shocks (administered with every 20th lick) is recorded on front panel counters. The performance of anti-anxiety drugs can be measured by comparing the drinking behaviour of punished drugged rats to the behaviour of punished non-drugged rats.The Vogel test is a conflict test has become a standard for fast screening the potential anxiolytic properties of drugs. In this procedure, the drinking behaviour is punished by mild electrical shocks leading to a significant reduction of water consumption in deprived animals. Drinking responses are then re-established by drugs with anxiolytic properties.Vogel Test Apparatus or Vogel Test Anxiometer is used for screening of anxiolytic effects of drugs on small laboratory animals like mice and rat.

Product Details:

The jolting apparatus consists of a rectangular table rigidly connected by two support arms to a spindle at a horizontal distance of 800 mm from the centre of the table. There is a projecting lug with a plane face on the upper face of the table beneath which is a stop with a rounded upper surface. The table can be raised and allowed to fall freely on the stop by a cam which is connected to a motor and gearbox through a V-belt an pulleys. The cam rotates at a rate of 60 Rev/Min. A stroke counter fitted with micro-switch is provided which stops the machine after 60 Jolts. Locating pins are provided for mounting the mould compartments on the table. The mould surmounted by the hopper can be clamped rigidly to the table. Supplied complete with mould and hopper.

Additional Information:

• Production Capacity: 50
• Delivery Time: Ex stock
• Packaging Details: wooden packing

Product DescriptionThis apparatus is used for determining the reactivity on slaking of ground quicklime.The equipment consists of a Dewar vessel 1000 ml capacity complete with cover, electric stirrer 300 rpm. complete with stirring paddle (propeller), base with stand, digital thermometer range -50 +200°C. subd. 0.1°C., accessories.

Capacity 16 BarUsage/Application Concrete Permeability ApparatusBrand EqvimechSurface Finish Powder CoatedInspect Depth 200mmDiameter 150mmMounting Type Easy ClampsShape Cube & CylinderStandards DIN 1048, EN 12390-8 & IS 516measuring cylinder 200 mmCountry of Origin Made in IndiaPOwer Requirement NoNo of Cells upto 24 nos

Product Details:

Product Description:

• Measures torsional modulus of rubber at low temperatures
• Holds ten samples
• Adjustable heating ramp rate
• Three torsion wires supplied
• Digital control box displays fluid temperature and ramp rate
• Using wires of known stiffness, this instrument determines the torsional modulus of vulcanized rubber samples at low temperature, consisting of a measuring unit and a separate controller.

The top of each torsion wire is attached to a head while the bottom is fastened to a pointer and a coupling to which each sample is clamped. The deflection of the torsion wire is easily read from a protractor, marked in 1O divisions.

Three catridges are supplied with the apparatus, having torsional constants of 0.70, 2.81, and 11.24 mNm/rad of twist respectively. Each torsion wire is mounted in an easily removable stainless steel “cartridge”, attached to the torsion head by a knurled screw for finger tightening.
A revolving 10 station test piece rack is mounted on the measuring head support so that each test piece may be indexed accurately under the torsion wire.

The bath consists of a removable stainless steel container located in an insulated box to which the heater/stirrer unit is attached by thumb screws.

The controller houses the speed control for the stirrer motor and a digital temperature controller which displays the fluid temperature and the ramp rate of heater.
Cutting ToolFor the special cutting tool, order